Cut-List Kit: plan PDF + spreadsheet
Chicken coop plans that recalculate to your size

A raised plywood hen house on four 2x4 legs, with a nest box, a roost, a pop door with a ramp, and a clean-out door. Type the floor size, the wall height and the leg height. The spreadsheet gives you the cut list, the cutting plan and the sheets and boards to buy.
Digital download: nothing is shipped. Opens our Etsy listing in a new tab. You pay on Etsy and Etsy delivers the files. This site takes no payment.
Price as listed on Etsy on 16 Nov 2026. Etsy may add tax, such as VAT, at checkout. If Etsy shows a different price, the Etsy price applies.
At a glance
- 24 to 59 inInside floor length (600 to 1500 mm)
- 20 to 39 inInside floor width (500 to 1000 mm)
- 20 to 39 inWall height (500 to 1000 mm)
- 4 sheets, 7 boardsto buy as the file arrives (mm default): 4 x plywood sheets, 3 x 2x4 boards, 4 x 2x2 boards
- 12build steps in the plan PDF
- 14 + 6pages: plan PDF and cutting diagram PDF
- mm or inone switch in the spreadsheet
- No macrostested in LibreOffice and Apple Numbers
The house is a plywood box raised on four 2x4 legs. The legs carry a 2x4 frame, and the floor panel is screwed down on top of it. The four walls stand on the floor, with a 2x2 batten in each inside corner to screw them to.
The roof is a single flat rectangle of plywood. It rests on two plywood strips of different heights, the taller one on the front wall, so it slopes without any angled cut. It reaches past every wall, and the triangle of air above each side wall stays open.
The pop door is in the front wall, with a hinged flap and a ramp that has 2x2 cleats across it. The nest box hangs on the outside of the back wall under a hinged lid. The clean-out door is in one side wall, above a sill whose height you type.
Every part starts as a plain rectangle, and three of the walls then get an opening. The pop door and the nest opening are each two straight cuts up from the bottom edge of a wall. The clean-out opening is cut out of the middle of a side wall. It is the only closed cut, and the plan names a jigsaw for it.
It is for someone who wants a small raised hen house and is happy cutting plywood with a circular saw or a hand saw. This is a house you reach into, not one you walk into. The spreadsheet stops the walls at 1000 mm (39 in) and the floor at 1500 x 1000 mm (59 x 39 in). The widest floors need a smaller roof overhang or a wider sheet: see the note under the sizes. It does not tell you how many hens that suits.
Sizes you can type
25 sizes, counts and switches are yours to set. The first four set the house: floor length, floor width, wall height and leg height. The next ones shape the roof, the two doors, the ramp, the nest box and the roost. The last five belong to the optional run.
The nest box takes 0 to 4 compartments and the roost 0 to 3 bars. Type 0 and those parts leave the cut list.
The pop door, nest box and roost sizes start at example values. The spreadsheet's own notes tell you to measure your birds and type your own.
-
Inside floor length front to back (wall to wall)
24 in600 mm59 in1500 mm
Starts at 1200 mm, or 48 in when the sheet is set to inches.
-
Inside floor width side to side (wall to wall)
20 in500 mm39 in1000 mm
Starts at 900 mm, or 36 in when the sheet is set to inches.
-
Wall height all four walls are this tall (inside floor surface to the top edge)
20 in500 mm39 in1000 mm
Starts at 900 mm, or 36 in when the sheet is set to inches.
The other 22 sizes, counts and switches
-
Leg height ground to the underside of the floor panel
8 in200 mm35 in900 mm
Starts at 500 mm, or 20 in when the sheet is set to inches.
-
Roof rise how much taller the tall bearer is than the low one (this is the whole slope)
3/8 in10 mm15 3/4 in400 mm
Starts at 150 mm, or 6 in when the sheet is set to inches.
-
Low bearer height (the low end of the roof, and the open gap over each side wall at the back)
3/4 in20 mm6 in150 mm
Starts at 60 mm, or 2 1/2 in when the sheet is set to inches.
-
Roof overhang the same on all four sides
0 in0 mm11 3/4 in300 mm
Starts at 100 mm, or 4 in when the sheet is set to inches.
-
Pop door width (the opening in the front wall; it reaches the floor)
6 in150 mm19 1/2 in500 mm
Starts at 300 mm, or 12 in when the sheet is set to inches.
-
Pop door height up from the inside floor surface
6 in150 mm23 1/2 in600 mm
Starts at 350 mm, or 14 in when the sheet is set to inches.
-
Ramp length (the plywood plank, from the pop door sill to the ground)
16 in400 mm78 in2000 mm
Starts at 1200 mm, or 48 in when the sheet is set to inches.
-
Clean-out door width (the opening in the side wall)
12 in300 mm39 in1000 mm
Starts at 500 mm, or 20 in when the sheet is set to inches.
-
Clean-out door height (the opening)
12 in300 mm39 in1000 mm
Starts at 500 mm, or 20 in when the sheet is set to inches.
-
Clean-out door sill solid side wall left below the opening, to hold the litter in
0 in0 mm11 3/4 in300 mm
Starts at 100 mm, or 4 in when the sheet is set to inches.
-
Nest box compartments
0 to 4; starts at 2
-
Width of each nest compartment along the back wall
10 in250 mm17 1/2 in450 mm
Starts at 300 mm, or 12 in when the sheet is set to inches.
-
Nest box depth out from the back wall (inside)
10 in250 mm17 1/2 in450 mm
Starts at 300 mm, or 12 in when the sheet is set to inches.
-
Nest box height (inside, under the flat lid)
10 in250 mm17 1/2 in450 mm
Starts at 300 mm, or 12 in when the sheet is set to inches.
-
Roost bars
0 to 3; starts at 1
-
Roost height inside floor surface to the top edge of the roost supports
6 in150 mm47 in1200 mm
Starts at 400 mm, or 16 in when the sheet is set to inches.
-
Roost pitch centre to centre between roost bars, front to back
10 in250 mm19 1/2 in500 mm
Starts at 350 mm, or 14 in when the sheet is set to inches.
-
Run
Yes or no; starts at no
-
Run length out from the house's front wall to the far posts' outer faces (run only)
40 in1000 mm157 in4000 mm
Starts at 2400 mm, or 96 in when the sheet is set to inches.
-
Run height ground to the top of the run's top rails (run only; capped at 1200 mm and at the roof underside)
24 in600 mm47 in1200 mm
Starts at 1200 mm, or 47 in when the sheet is set to inches.
-
Run door at the far end
Yes or no; starts at yes
-
Run door width (run door only)
16 in400 mm35 in900 mm
Starts at 600 mm, or 24 in when the sheet is set to inches.
The largest floors and the default sheet
The file starts in millimetres, with 2440 x 1220 mm plywood sheets and a roof overhang of 100 mm (in inches: 96 x 48 in sheets and a 4 in overhang). With those, the roof panel no longer fits on one sheet once both floor sides are over about 38 1/2 in (980 mm). The Status line then reads INCOMPLETE and flags the roof panel.
A roof overhang of 3 3/4 in or less clears it, even at the largest floor, 59 x 39 in. So does a wider sheet, if you can buy one.
Your stock
Type the real sizes of the boards and sheets you buy. The spreadsheet starts with these:
- Plywood sheet
96 x 48 in, 3/4 in thick (2440 x 1220 mm, 18 mm thick) - 2x4 board
96 in long, 3 1/2 x 1 1/2 in (2440 mm long, 89 x 38 mm) - 2x2 board
96 in long, 1 1/2 x 1 1/2 in (2440 mm long, 38 x 38 mm)
Also yours to type
- Saw kerf (blade width)
- Your price for each board or sheet
- 8 advanced settings, each with its own range
A size outside its range is refused: the Status line reads CHECK INPUTS instead of OK.
What changes when you type
The file arrives set to millimetres, at 1200 x 900 mm inside. The PDFs are drawn at that size. It needs 4 plywood sheets, 3 2x4 boards and 4 2x2 boards.
Switch the sheet to inches and it starts from round inch values, 48 x 36 in, which is a slightly bigger house. It then asks for 5 sheets, 3 2x4 boards and 5 2x2 boards. Typed at 59 x 38 in, the same file asks for 6, 3 and 5.
Switch the run on at the inch defaults and the 2x4 count goes from 3 to 11.
The Chicken Coop spreadsheet at two sizes
| Inch default | Larger | |
|---|---|---|
| You type | ||
| Inside floor length | 48 in | 59 in |
| Inside floor width | 36 in | 38 in |
| The spreadsheet answers | ||
| Status | OK | OK |
| Plywood sheets to buy | 5 | 6 |
| 2x4 boards to buy | 3 | 3 |
| 2x2 boards to buy | 5 | 5 |
Read back from the file on sale after LibreOffice recalculated it at each size, on 14 Nov 2026. Every other input was left at its inch default.
What is in the download
Four files. The spreadsheet comes inside the zip, because Etsy does not take spreadsheet uploads.
The plan PDF has a page for the three walls with their openings, a page for the nest box, the roost and the ramp, and a page for the run. The cutting diagram gives the plywood sheets four of its six pages.
- cut-list-kit.zip
Holds the spreadsheet itself, plus a copy of each PDF and parts.csv, the cut list in a form any spreadsheet can import. Unzip it on a computer. On a phone, a file-manager app can open it.
- cutlist-calculator.xlsx
- plan.pdf
- cutting-diagram.pdf
- parts.csv
- plan.pdf
14 pages. Drawings with every dimension, the hardware list, 12 numbered build steps and the cut list, all at the default size.
- cutting-diagram.pdf
6 pages: which part is cut from which board or sheet, at the default size.
- parts.txt
The default-size cut list as plain text, for reading on a phone.
Sample pages
How it goes together
The plan PDF has 12 written steps. These eight pictures follow the house from the floor frame up to the nest box. They are drawn with the run switched off. The run and its door are steps 10 and 11 in the PDF.
The written steps were drafted with AI help. The drawings and the cut list are generated by code from one model of the build.

Floor frame: two long rails and two end rails on edge, a leg standing in each inside corner

Floor panel laid on the frame, overhanging it by the frame set-in on all four sides

A corner batten in each inside corner, then the two side walls: one plain, one with the clean-out opening

Roost support flat against each side wall's inside face, top edge at the roost height; the roost bar across them

Front wall with the pop door opening and back wall with the nest opening, outside faces flush with the floor's edges

Tall bearer on the front wall, low bearer on the back; the roof panel lies on both, falls to the back and overhangs all round

Pop door flap hinged above the opening (shown held open), the cleated ramp from the ground to the sill, the clean-out door on the side wall

Nest box on the outside of the back wall: floor level with the house floor, two ends, the divider, the front, and the flat lid hinged to the wall
Software renderThe 8 pictures show the main stages at the default size, drawn from the plan's own part sizes. They are not photographs. The plan PDF has all 12 written steps.
What you need
The house is cut from plywood sheets, 2x4 boards for the frame and legs, and 2x2 boards for the battens, roost and ramp cleats. The spreadsheet starts with sheets 96 x 48 in, 3/4 in thick, and boards 96 in long.
At the default size the hardware list counts 6 hinges and 3 latches, two hinges and one latch for each door and lid. Screws, glue and filler are counted as well. Mesh for the run is given as a plain area. The plan names no roofing felt or other covering: the plywood panel is the roof.
Stock at the default size
- 4plywood sheets
- 32x4 boards
- 42x2 boards
Your own size changes these counts. The spreadsheet gives the new ones.
Counted, not priced
Floor-to-frame screws, base screws, wall screws, bearer screws, roof screws, short frame screws, long frame screws, nest box screws, roost screws, ramp cleat screws, short run screws, long run screws, rail-to-house screws, run door frame screws, hinges, latches or hooks, mesh for the run and staples, wood glue, exterior wood filler.
The spreadsheet totals the timber cost from the prices you type. Hardware is counted or measured, not priced: screws, hinges, latches and mesh not priced.
Tools the plan names
- Circular saw or hand saw
- Jigsaw for the one closed opening
- Drill/driver
- Countersink bit
- Square
- Tape
- Level
- Screwdriver
Opening the spreadsheet
The file is cutlist-calculator.xlsx. It has no macros, so nothing needs enabling.
This kit's file was tested in LibreOffice, which is free, and in Apple Numbers. The automated test ran all 56 sets of inputs in LibreOffice and eight of them in Apple Numbers. We have not tested it in Excel or Google Sheets, so we do not promise it works there.
The test record for this file
- 133,256automated checks
- 0failed
- 56sets of inputs: 43 inside the ranges, 13 bad ones that must be refused
- 20 Oct 2026date of the test report
The test compares the spreadsheet with a separate program's results. It covers the arithmetic and the cutting plan, not the design, and it is not a physical build. How we check every kit
What this plan does not do
This is a plan and a calculator, not an engineered product. It gives no rating for strength, weather, ventilation or predators, and no figure for how many birds the house or the run suits. The plan's own wording follows in full. Read it before you buy.
Safety note, as printed in the plan
- This is a plan for a chicken coop and run.
- It makes NO rating of any kind: no load, weight, strength, stability, wind, snow, rot or weather rating for the legs, the frame, the floor, the roof, the roosts, the ramp or the run; no ventilation, temperature, insulation or draught rating for the house; no predator, security, mesh or fastening rating for the run, the doors, the nest lid or the pop door; and no welfare rating - nothing here says how many birds, or which birds, this house or run is right for, how much floor, roost, nest or run space a bird needs, or whether the pop door, ramp, roost height or nest box suit your flock.
- The nest box count, the roost count and every size are numbers you type; the plan does not turn a flock into a size.
- No person may stand, sit, climb or lean on any part of it; the house walls are held to 1000 mm and the run to 1200 mm high because neither is a building for a person to enter, and the doors, lid, flap and latches are counted, not rated: nothing here is a security claim.
- Mesh, hinges, latches, roofing felt and any covering are counted or named, not specified.
- Stand it on firm, level ground, and check every part against the cut list before assembly.
- The doors close; this plan makes no predator, escape, containment or security rating of any kind.
One sentence per line here; the words are the plan's own.
17 things the spreadsheet does not work out
- Any welfare figure: how many birds the house or the run is for, floor space, roost length or nest boxes per bird, pop door size for a breed, ramp angle a bird will use, or whether the heights suit your birds. You type the sizes and the counts; nothing here turns a flock into a size.
- Any ventilation, temperature, insulation, draught, damp or condensation figure. The open wedge over each side wall is a geometric fact of the build - its sizes are printed - and nothing here says whether that is the right amount of airflow for your climate or your birds.
- Any predator, security, fastening or mesh rating. The mesh area is a plain area in square metres and square feet with no gauge, aperture, material, burial depth, staple count or strength; the hinges and latches are counted, not sized; no part of this plan says what will keep an animal out or a bird in.
- Any load, weight, strength, stability or tipping rating for the legs, the frame, the floor, the roosts, the nest box, the ramp, the roof or the run posts and rails. No span, deflection or stiffness check of any kind is made.
- Weather, water, rot, insects or how long any part lasts outdoors. The legs and the run posts stand on the ground and every cut end is left open unless you treat it; the nest lid is flat and nothing is said about water on it.
- Roofing felt, shingles, metal sheet, sealant or any covering over the plywood roof panel or the nest lid: the panels are the roof in this plan, and nothing is specified over them.
- Plan (horizontal) overhang. The roof panel sizes are measured ALONG the panel, which lies on a slope, so the horizontal reach past the walls is a little less than the overhang you typed; the spreadsheet has no square root and does not work it out. The roof panel's thickness is added square to its face in the overall heights for the same reason.
- The ramp's angle in degrees. The ramp rises from the ground to the inside floor surface over the ramp length you type; the advisory that calls it steep uses one fixed fact (a slope that climbs its length in half its length is 30 degrees) and nothing else.
- Where exactly to hinge, latch or hook each door and the lid, which hinge or latch to buy, and any stop, catch, prop or stay. Two hinges and one latch per door and lid are counted; nothing is sized or placed.
- The mesh door's own stiffness, a diagonal brace for it, or any brace anywhere in the run: the frames are plain rectangles screwed at the corners and nothing says they will stay square under use.
- Anchoring the coop or the run to the ground or to each other beyond the screws listed, and the pegs, straps or fixings to do it with; naming one would be a strength claim.
- Which timber, plywood or mesh to buy: species, grade, treatment, exterior rating, ground-contact rating or food-animal safety of any finish. Check the maker's own figures.
- Litter, bedding, feeders, waterers, a droppings board, a window, electrics, heating or lighting of any kind.
- Wood grain direction, knots, warp, voids or other defects in your stock; trimming factory ends beyond the saw kerf you enter.
- The price of the screws, hinges, latches, mesh and staples: they are counted or named, not priced; staples for the mesh are not counted.
- Board-feet: boards and sheets are counted as whole pieces.
- A guaranteed minimum number of boards or sheets. The cutting plan is good, but it is not proven to be the fewest possible, and the Cut List also shows a lower bound that no plan can beat.
The list is copied from the kit's own files, so it matches what you download.
AI pictures of the finished build
These two pictures were made by an AI image tool. They are not photographs, and we have not built or photographed a coop from this plan.
The first shows the coop with its optional run. The run is a switch in the spreadsheet, and it is off when the file arrives. The second shows the house alone.
Treat both as rough impressions. The proportions are approximate. The mesh, hinges, latches and chain in them are the AI's guess: the plan counts hinges and latches, and gives the mesh as an area, but specifies none of them. The drawings and the cut list are what you build from.


Questions about this kit
How many hens does this coop hold?
The plan does not work that out. You type the floor size, the number of nest compartments and the number of roost bars. The spreadsheet's own labels call those counts examples and say that nothing works them out from your birds.
Is the run part of the kit?
Yes, as an option. One cell switches it on. It is a frame of 2x4 posts and rails, the full width of the house, built out from the front wall and 40 to 157 in long. Its height stops at 1200 mm (47 in). A mesh door frame at the far end is a second switch. The mesh is given as an area, not chosen for you.
Do I have to cut angles for the sloping roof?
No. The slope comes from two plywood strips of different heights, one on the front wall and one on the back. You type how much taller the front one is, from 3/8 to 15 3/4 in.
What goes over the plywood roof?
The plan specifies nothing over it. The roof panel and the nest lid are bare plywood in this plan, and the plan gives no weather rating. Any felt, sheet or sealant is your choice.
Can I leave out the nest box or the roost?
Yes. Type 0 for nest compartments or 0 for roost bars. Those parts then leave the cut list and their build steps do not apply.
Which program opens the spreadsheet?
LibreOffice Calc, which is free, or Apple Numbers. Those are the two programs this kit's file was tested in. We have not tested it in Excel or Google Sheets.
Chicken Coop Cut-List Kit
Digital download: nothing is shipped. Opens our Etsy listing in a new tab. You pay on Etsy and Etsy delivers the files. This site takes no payment.
Price as listed on Etsy on 16 Nov 2026. Etsy may add tax, such as VAT, at checkout. If Etsy shows a different price, the Etsy price applies.
Questions first? Message us on Etsy (opens in a new tab). See refunds and delivery.






